 |
|
PT-DW10000 |
| DLP™chip |
Panel size |
0.95" diagonal
(16:9 aspect ratio) |
| Display method |
DLP™ chip
x 3 (R, G, B), DLP™ projection system |
| Pixels |
2,073,600
(1,920 x 1,080) x 3, total of 6,220,800 pixels |
| Lamp |
250
W UHM lamp x 4 (four lamp system) |
| Brightness*1 |
10,000 lumens (four-lamp operation
mode) |
| Contrast
ratio*1 |
5,000:1 (full
on/full off, in Dynamic iris 3 mode) |
| Resolution |
1,920 x 1,080
pixels (1,600 x 1,200 pixels compatible, compression mode) |
| Lens |
Optional powered
zoom/focus lenses |
| Screen
size |
70 - 600 inches,16:9
aspect ratio
(70-300 inches, 16:9 aspect ratio with the ET-D75LE5) |
| Lens shift |
Vertical: ±60% (±50° with the ET-D75LE6) from center of screen, powered
Horizontal: ±20% (±15° with the ET-D75LE6) from center of screen, powered |
| RGB input scanning frequency |
fH 15-100 kHz, fV 24-120 Hz
Dot clock 20-162 MHz |
| Component
signal |
480i, 480p,
576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p |
| Video
signal |
fH 15.75/15.63
kHz, fV 50/60Hz
(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM) |
| Terminals |
VIDEO IN |
BNC x 1, 1.0 Vp-p |
| VIDEO OUT |
BNC x 1, 1.0 Vp-p |
| S-VIDEO IN |
Mini DIN 4-pin
x 1 |
| RGB 1 / YPBPR IN |
BNC x 5 |
| RGB 2 IN |
D-sub HD 15-pin
x 1 |
| DVI-D IN |
24-pin x1,
DVI 1.0 compliant, HDCP compatible |
| SERIAL IN |
D-sub 9-pin
female x 2 (RS232C x 1, RS422 x 1) |
| SERIAL OUT |
D-sub 9-pin
male x 1 (RS422 x 1) |
| REMOTE 1
IN |
M3 jack x1
for wired remote control |
| REMOTE 1
OUT |
M3 jack x1
for link control |
| REMOTE 2
IN |
D-sub 9-pin
female x 1 for external control (parallel) |
| LAN |
RJ-45 (10
Base-T/100 Base-TX) x 1, compatible with PJLink™ |
| Optional board slot |
With ET-MD77SD1 installed |
| SERIAL IN: |
|
BNC x 1
SD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i |
| SERIAL OUT: |
|
BBNC x 1, active through |
| NOTE: |
|
LAN terminals on the optional board can not be used. Use the LAN terminal on the projector. |
|
| With ET-MD77SD3 installed |
| SERIAL IN: |
|
BNC x 1
SD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i
Single-link HD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 292M compliant 720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p |
| SERIAL OUT: |
|
BNC x 1, active through |
| NOTE: |
|
LAN terminals on the optional board can not be used. Use the LAN terminal on the projector. |
|
| With ET-MD100SD4 installed |
| Link A/Link B IN: |
|
BNC x 1 for each
SD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i
Single-link HD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 292M compliant, 720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p,1080/24p, 1080/24sF, 1080/30p
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit) : SMPTE 372M compliant, 1920 x 1080/50i, 1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit) : 2048 x 1080/24p, 2048 x 1080/24sF |
| NOTE: |
|
LAN terminals on the optional board can not be used. Use the LAN terminal on the projector. |
|
| With ET-MD77DV installed |
| DVI-D IN: |
DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
EDID1: 480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, 720/60p, 720/50p
EDID2: Compatible with non-interlaced signal only, VGA(640 x 480) - U-XGA (1,600 x 1,200), dot clock: 25 - 162 MHz |
| NOTE: |
|
LAN terminals on the optional board can not be used. Use the LAN terminal on the projector. |
|
| Keystone
correction range |
±40° (±22° with
the ET-D75LE5, ±28° with the ET-D75LE6) |
| Installation |
Front/rear,
ceiling/floor |
| Power
cord length |
9.9'' (3.0
m) |
| Power
supply |
PT-DW10000U
(North
America) |
120VAC, 15A,
60Hz |
PT-DW10000E
(Europe, Asia) |
220-240VAC,
15A, 50/60Hz |
| Power
consumption |
1,450 W (25
W in standby mode with fan stopped) |
| Dimensions
(W x H x D) |
22-3/4'' x
12-19/32'' x 25-5/16'' (578 x 320 x 643 mm) (without lens) |
| Weight |
70.5 lbs (32
kg) without lens |
| Operating
temperature |
32 -113 °F
(0 -45°C)
*The highland mode is for use at high altitudes. When using the unit
at altitudes of 1,400 to 2,700 meters, the ambient temperature is 0°C-40°C. |
| Operating
humidity |
10-80% (no
condensation) |
| Supplied
accessories |
Power cord,
Wireless/wired remote control unit,
Batteries for remote control ( AA type for North/South America, R6/LR6 type for Europe / Asia) x 2 |
|
