PT-VW330 Series

LCD Projectors PT-VW330 PT-VX400NT PT-VX400 PT-VX41

Specifications

PT-VW330 / VX400NT / VX400

Model PT-VW330 PT-VX400NT PT-VX400
Power supply 100-240 V AC, 50/60 Hz
Power consumption 322 W (0.48 W when
standby mode
set to Eco*1,
12.5 W when standby mode
set to Network.)
322 W (0.48 W when
standby mode
set to Eco*1,
14.5 W when standby mode
set to Network.)
322 W (0.48 W when
standby mode
set to Eco*1,
10.0 W when standby mode
set to Network.)
LCD panel Panel size 15 mm (0.59 inches)
diagonal (16:10 aspect ratio)
16 mm (0.63 inches)
diagonal (4:3 aspect ratio)
Display method Transparent LCD panel (x 3, R/G/B)
Pixels 1,024,000 (1,280 x 800) x 3,
total of 3,072,000 pixels
786,432 (1,024 x 768) x 3, total of 2,359,296 pixels
Lens 1.6x manual zoom (throw ratio: 1.2–1.9:1), manual focus, F 1.65–2.33, f 15.47–24.53 mm
Lamp 245 W x 1, lamp replacement cycle (lamp power: Normal/Eco1, Eco2):
3,000 hours/5,000 hours*2
Screen size (diagonal) 0.76–7.62 m (30–300 inch)
Brightness 3,000 lm
(lamp power: Auto/Normal)
4,000 lm
(lamp power: Auto/Normal)
Center-to-corner uniformity*3 85 %
Contrast 2,000:1 (full on/full off, lamp power: Auto)
Resolution 1,280 x 800 pixels*4 1,024 x 768 pixels*5
Scanning frequency HDMI fH: 25–80 kHz, fV: 50–85 Hz, dot clock: 162 MHz or lower
RGB (analog) fH: 15–100 kHz, fV: 50–100 Hz, dot clock: 140 MHz or lower
(Signals exceeding the dot clock rate of 140 MHz are downsampled.)
YPBPR (YCBCR)
fH: 15.75 kHz, fV: 60 Hz [480i(525i)]
fH: 31.50 kHz, fV: 60 Hz [480p(525p)]
fH: 45.00 kHz, fV: 60 Hz [720(750)/60p]
fH: 33.75 kHz, fV: 60 Hz [1080(1125)/60i]
fH: 15.63 kHz, fV: 50 Hz [576i(625i)]
fH: 31.25 kHz, fV: 50 Hz [576p(625p)]
fH: 37.50 kHz, fV: 50 Hz [720(750)/50p]
fH: 28.13 kHz, fV: 50 Hz [1080(1125)/50i]
Video/S-Video fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60],
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Optical axis shift 49:1 9:1
Keystone correction range Vertical: ±30°
(±20° when Real-Time
Keystone)
Vertical: ±40°, Horizontal: ±30°
(Vertical: ±30°, Horizontal: ±20°
when Auto Keystone)
Vertical: ±30°
(±20° when Real-Time
Keystone)
Installation Ceiling/floor, front/rear
Terminals HDMI IN HDMI 19-pin x 1 (compatible with HDCP)
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/60p, 1080/50p,
VGA (640 x 480)-WUXGA (1,920 x 1,200), *6
audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
COMPUTER IN 1 D-sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR x 1)
COMPUTER IN 2
/ MONITOR OUT
D-sub HD 15-pin (female) x 1 (RGB x 1), (input/output selectable using on-screen menu)
(When Monitor Out is selected, the COMPUTER IN 1 signal is output.)
VIDEO IN Pin jack x 1 (Composite VIDEO)
S-VIDEO IN Mini DIN 4-pin x 1 (S-VIDEO)
AUDIO IN Pin jack x 2 (L-R x 1) for VIDEO/S-VIDEO input
COMPUTER
AUDIO IN 1
M3 x 1 (L-R x 1)
COMPUTER
AUDIO IN 2
(MIC IN)
M3 x 1 (L-R x 1) for audio input or for microphone connection (variable)
AUDIO OUT M3 x 1 (L-R x 1) for output (variable)
SERIAL IN D-sub 9-pin (male) x 1 for external control (RS-232C compliant)
LAN RJ-45 x 1 (for network connection, 10Base-T/100Base-TX,
compliant with PJLink™ (class 1))
USB A - USB type-A
(for the USB Memory
Viewer) x 1
-
USB B - USB type-B
(for the USB Display/
Wireless Mouse) x 1
-
Built-in speaker 3.7 cm round shape x 1, output power: 10.0 W (monaural)
Noise level 35 dB (lamp power: Normal), 29 dB (lamp power: Eco1, Eco2)
Cabinet materials Molded plastic
Dimensions (W x H x D) 350 x 97 x 277 mm (13.8" x 3.8" x 10.9")
(with legs at shortest position, not including protruding parts)
Weight Approx. 3.5 kg (7.7 lbs) Approx. 3.6 kg (7.9 lbs) Approx. 3.5 kg (7.7 lbs)
Operating environment Operating temperature: 5°C–35°C (41°F–95°F),
operating humidity: 20%–80% (no condensation)
Wireless Standard - IEEE802.11b/g/n -
Infrastructure mode - WPA-PSK(TKIP/AES),
WPA2-PSK(TKIP/AES),
128 bit/64 bit WEP,
WPA-EAP/WPA2-EAP
(PEAP[MS-CHAPv2/GTC],
EAP-FAST[MS-CHAPv2/GTC],
EAP-TTLS[MD5/MS-CHAPv2])
-
Ad-hoc mode*7 - 128 bit/64 bit WEP -
Supplied accessories Power cord x 1*8, wireless remote control unit,
batteries (AAA/R03/LR03 type x 2), carrying bag x 1, RGB cable x 1, filter cover
Software CD-ROM
(Logo Transfer Software,
Multi Projector Monitoring &
Control Software)
Software CD-ROM
(Logo Transfer Software,
Multi Projector Monitoring &
Control Software,
Wireless Manager ME 5.5)
Software CD-ROM
(Logo Transfer Software,
Multi Projector Monitoring &
Control Software)
*1
When the Standby mode is set to Eco, network functions such as standby on via LAN are not available. Also, only certain commands can be received for external control using the serial terminal.
*2
The values given for the recommended lamp replacement cycles are maximum.
*3
Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4
Input signals that exceed this resolution will be converted to 1,280 x  800 pixels.
*5
Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.
*6
Compliant with VESA CVT-RB.
*7
Not supported by IEEE802.11n.
*8
Power cords available (x 2) for the PT-VW330EA/VX400NTEA/VX400EA.

PT-VX41

Model PT-VX41
Power supply 100-240 V AC, 50/60 Hz
Power consumption 322 W (0.48 W when standby mode set to Eco*1,
10.0 W when standby mode set to Network.)
LCD panel Panel size 16 mm (0.63 inches) diagonal (4:3 aspect ratio)
Display method Transparent LCD panel (x 3, R/G/B)
Pixels 786,432 (1,024 x 768) x 3, total of 2,359,296 pixels
Lens 1.2x manual zoom (throw ratio: 1.7–2.1:1), manual focus, F 1.60–1.76, f 22.33–26.80 mm
Lamp 245 W x 1, lamp replacement cycle (lamp power: Normal/Eco1, Eco2):
3,000 hours/5,000 hours*2
Screen size (diagonal) 1.02–7.62 m (40–300 inch)
Brightness 4,000 lm (lamp power: Auto/Normal)
Center-to-corner uniformity*3 85%
Contrast 2,000:1 (full on/full off, lamp power: Auto)
Resolution 1,024 x 768 pixels
(Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.)
Scanning frequency HDMI fH: 25–80 kHz, fV: 50–85 Hz, dot clock: 162 MHz or lower
RGB (analog) fH: 15–100 kHz, fV: 50–100 Hz, dot clock: 140 MHz or lower 
(Signals exceeding the dot clock rate of 140 MHz are downsampled.)
YPBPR (YCBCR)
fH: 15.75 kHz, fV: 60 Hz [480i(525i)]
fH: 31.50 kHz, fV: 60 Hz [480p(525p)]
fH: 45.00 kHz, fV: 60 Hz [720(750)/60p]
fH: 33.75 kHz, fV: 60 Hz [1080(1125)/60i]
fH: 15.63 kHz, fV: 50 Hz [576i(625i)]
fH: 31.25 kHz, fV: 50 Hz [576p(625p)]
fH: 37.50 kHz, fV: 50 Hz [720(750)/50p]
fH: 28.13 kHz, fV: 50 Hz [1080(1125)/50i]
Video/S-Video fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60], 
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Optical axis shift 9:1
Keystone correction range Vertical: ±30° (±20° when Real-Time Keystone)
Installation Ceiling/floor, front/rear
Terminals HDMI IN HDMI 19-pin x 1 (compatible with HDCP)
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/60p, 1080/50p, 
VGA (640 x 480)-WUXGA (1,920 x 1,200), *4
audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
COMPUTER IN 1 D-sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR x 1)
COMPUTER IN 2
/ MONITOR OUT
D-sub HD 15-pin (female) x 1 (RGB x 1), (input/output selectable using on-screen menu) 
(When Monitor Out is selected, the COMPUTER IN 1 signal is output.)
VIDEO IN Pin jack x 1 (Composite VIDEO)
S-VIDEO IN Mini DIN 4-pin x 1 (S-VIDEO)
AUDIO IN Pin jack x 2 (L-R x 1) for VIDEO/S-VIDEO input
COMPUTER
AUDIO IN 1
M3 x 1 (L-R x 1)
COMPUTER
AUDIO IN 2
(MIC IN)
M3 x 1 (L-R x 1) for audio input or for microphone connection (variable)
AUDIO OUT M3 x 1 (L-R x 1) for output (variable)
SERIAL IN D-sub 9-pin (male) x 1 for external control (RS-232C compliant)
LAN RJ-45 x 1 (for network connection, 10Base-T/100Base-TX,
compliant with PJLink™ (class 1))
Built-in speaker 3.7 cm round shape x 1, output power: 10.0 W (monaural)
Noise level 35 dB (lamp power: Normal), 29 dB (lamp power: Eco1, Eco2)
Cabinet materials Molded plastic
Dimensions (W x H x D) 350 x 97 x 254 mm (13.8" x 3.8" x 10.0") 
(with legs at shortest position, not including protruding parts)
Weight Approx. 3.4 kg (7.5 lbs)
Operating environment Operating temperature: 5°C–35°C (41°F–95°F), 
operating humidity: 20%–80% (no condensation)
Supplied accessories Power cord x 1*5, wireless remote control unit, batteries (AAA/R03/LR03 type x 2),
carrying bag x 1, RGB cable x 1, filter cover,Software CD-ROM (Logo Transfer Software,
Multi Projector Monitoring &Control Software) x 1
*1
When the Standby mode is set to Eco, network functions such as standby on via LAN are not available. Also, only certain commands can be received for external control using the serial terminal.
*2
The values given for the recommended lamp replacement cycles are maximum.
*3
Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4
Compliant with VESA CVT-RB.
*5
Power cords available (x 2) for the PT-VX41EA.
Caution
Do not install the projector in locations that are subject to excessive water, humidity, steam or oily smoke. Doing so may result in fire, malfunction or electric shock.
NOTES ON USE
1 The projector uses a high-voltage mercury lamp under high internal pressure. This lamp may break, emitting a popping sound, or fail to illuminate, due to impact or extended use.
2 The high-wattage lamp becomes very hot during operation. Please observe the following precautions:
• Never place objects on top of the projector while it is in operation.
• Make sure there is an unobstructed space of 1,000 mm (39-3/8 in) or more around the projector’s exhaust openings.
• If stacking projector units, care must be taken to provide the recommended space between units. These space requirements also apply to installation
  where only one projector unit is operating at one time and the other unit is used as a backup.
• If the projector is placed in a box or enclosure, the temperature of the air surrounding the projector must match the operating temperature listed in the
  specifications table during use. Also, make sure the projector’s intake and exhaust openings are not blocked. Ensure there is sufficient ventilation to
  prevent hot air from the exhaust openings being recirculated into the intake opening.
3 The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The lamp replacement cycle varies greatly depending on individual lamp characteristics and usage conditions.
• The brightness of the lamp will gradually decrease with use.
4 Due to natural characteristics of lamps, screen brightness may fluctuate. This is not an indication of faulty lamp performance.