FAQs Contents

Images from multiple cameras can be displayed on a multi-screen. Images from 4 cameras (up to 16 cameras) can be displayed simultaneously. To display images on a multi-screen, it is necessary to register cameras in advance.
4 cameras can be registered as a group and up to 4 groups (16 cameras) can be registered.
The following is important.
*When displaying images on a 16-screen, panning, tilting and zooming operations become unavailable for images from the Panasonic PTZ cameras.
*When displaying images on a 4-screen, panning, tilting and zooming operations become available only for images from the Panasonic PTZ cameras. Refer to the readme file on the provided CD-ROM for further information about the compatible PTZ cameras and their versions.
*Only JPEG images can be displayed on a multi-screen.
*Audio will not be heard.
*When the power is turned off or the Ethernet cable is disconnected while displaying images, displaying images on a multi-screen from the "Live" page will become unavailable.
*Regardless of the settings of the registered device, the images will be displayed altered to the aspect ratio of 4:3 on a multi-screen.

WJ-GXE500

The status of the SD recording can be checked with the indicator. When the SD recording starts, this indicator will light red. When the SD recording stops, this indicator will
go off. This indicator will be displayed only when "Manual"is selected for "Save trigger" on the setup menu.

WJ-GXE500

User name: admin
Password: 12345

The following security functions are featured in this unit.
① Access restrictions by the host authentication and the user authentication
It is possible to restrict users from accessing the unit by setting the host authentication and/or the user authentication to "On".
② Access restrictions by changing the HTTP port
It is possible to prevent illegal access such as port scanning, etc. by changing the HTTP port number.

WJ-GXE500

It is necessary to install the viewer software "Network Camera View 4" to display images on a PC.
This software can be installed directly from the network video encoder WJ-GXE500 or WJ-GXE500E (hereinafter, the unit) or by double clicking "nwcv4setup.exe" on the CD-ROM provided, and then following the on-screen
instructions.

WJ-GXE500

The alarm occurrence factor bit will only be 111 or 000. If the alarm is received from the connector of the main device, the occurrence factor bit will be 111. The connector number bit will contain the number of the connector when the alarm occurred. If the alarm is received from the encoder, an expansion area is appended.

Register it not as a "camera" but as an "encoder".

Off is selected for "H.264 (or MPEG-4) transmission"
"Ch1 only" is selected JPEG (VGA, QVGA, D1): 30 fps (NTSC model), 25 fps (PAL model)
"Ch1-2" is selected JPEG (VGA, QVGA, D1): 15 fps (NTSC model), 12.5 fps (PAL model)
"Ch1-3" is selected: JPEG (VGA, QVGA, D1): 15 fps (NTSC model), 12.5 fps (PAL model)
"Ch1-4" is selected : JPEG (VGA, QVGA, D1): 15 fps (NTSC model), 12.5 fps (PAL model)

"On" is selected for "H.264 (or MPEG-4) transmission"
"Ch1 only" is selected JPEG (VGA, QVGA, D1): 15 fps (NTSC model), 12.5 fps (PAL model)
"Ch1-2" is selected JPEG (VGA, QVGA, D1): 15 fps (NTSC model), 12.5 fps (PAL model)
"Ch1-3" is selected: JPEG (VGA, QVGA, D1): 10 fps (NTSC model), 8.3 fps (PAL model)
"Ch1-4" is selected : JPEG (VGA, QVGA): 3 fps (NTSC model), 3.1 fps (PAL model) JPEG (D1): 2 fps (NTSC model), 2.1 fps (PAL model)

AUX control buttons have been removed, but CGI still exists. Therefore, AUX control is available just like the previous encoders.

13 Mbps.

You must send a keepalive command within 120 seconds (recommended: every 10 to 30 seconds)

[Relevant devices: WV-NP244, WV-NF282, WV-NS202, WV-NS202A, WV-NW484S, WV-NS954, WV-NW964, WV-NF302, WV-NP304, WV-NP1000, WJ-NT304, WJ-NT314]

Cameras are operating according to specification, which was set for the following two reasons:
(1) To prevent indefinite sound amplification by camera after an operator has used public addressing and forgot about it.
(2) To avoid the situation where sound amplification is unavailable for other users, since sound amplification can only be used by 1 user at a time.

[Relevant devices: WV-NS202, WV-NS202A, WV-NW484S, WV-NS954, WV-NW964, WV-NF302, WV-NP304, WV-NP1000, WJ-NT304, WJ-NT314]

We have not confirmed compatibility with AdjustPC. However, according to our experience, time synchronization had been possible with the software until around 2007, and began to fail after some update to the operating system.
Currently we have no recommended NTP software. An NTP server for Windows is available. Please see the article for details. * We confirmed that NTP-based synchronization is possible at this point, but permanent operation cannot be guaranteed.

Start Internet Explorer 9 → [Tools], check turn off "ActiveX Filtering".

Click here for more details.