Turnkey Solution for Multi Window PresentationsTurnkey Solution for Multi Window Presentations
ET-MWP100G
Power supply 100-240 V AC, 50/60 Hz
Power consumption 160 W max. (180 W with the ET-RPS100G)
Board mounting slots 16 slots (including two dedicated input slots and two dedicated output slots)
Scanning frequency with the ET-MCYSD200
SDI 3G-SDI signal (Level A YPBPR 4:2:2 10-bit):
SMPTE ST 424 compliant: 1125 (1080)/60p, 1125 (1080)/50p
Scanning frequency with the ET-MCYSD200/MCYSD210
SDI HD-SDI signal (YPBPR 4:2:2 10-bit):
SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/30p
SD-SDI signal (YPBPR 4:2:2 10-bit):
SMPTE ST 259 compliant: 525i(480i), 625i(576i)
Scanning frequency with the ET-MCYDV100
DVI-U (digital) fH: 15.6-82.2 kHz, fV: 24.0-85.1 Hz, dot clock: 25.2-162 MHz
RGB fH: 15.6-82.2 kHz, fV: 24.0-85.1 Hz, dot clock: 162 MHz or lower
YPBPR(YCBCR)
  • fH: 15.75 kHz, fV: 60 Hz [480i (525i)]
  • fH: 31.50 kHz, fV: 60 Hz [480p (525p)]
  • fH: 15.63 kHz, fV: 50 Hz [576i (625i)]
  • fH: 31.25 kHz, fV: 50 Hz [576p (625p)]
  • fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p]
  • fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p]
  • fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i]
  • fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i]
  • fH: 28.13 kHz, fV: 25 Hz [1080 (1125)/25p]
  • fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p]
  • fH: 33.75 kHz, fV: 30 Hz [1080 (1125)/30p]
  • fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p]
  • fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p]
Video/S-Video fH: 15.75 kHz, fV: 60 Hz [NTSC], fH: 15.63 kHz, fV: 50 Hz [PAL]
Terminals
SERIAL IN D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
LAN RJ-45 x 1 for external control, 100Base-TX/10Base-T
USB Type A x 1 (front), Type B x 1 (rear), for service
Dimensions (W x H x D) 482 x 177 x 313 mm (19.0" x 11.6" x 12.4")
Weight*1 Approximately 9.6 kg (21.16 lbs) (when optional devices are mounted)
Operating environment Operating temperature: 0-40 °C (32-104 °F)*2, operating humidity: 10-85 % (no condensation)
Supplied accessories Power cord (x 3), software CD-ROM (Control Software for Multi Window Processor)

Optional Interface Boards

  ET-MCYDV100
DVI-U IN
DVI-U IN DVI-U 29-pin x 2
Digital DVI 1.0 compliant, compatible with HDCP, for single link only
525i (480i),*3 625i (576i),*3 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p,
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/25p, 1125 (1080)/24p, 1125 (1080)/30p,
1125 (1080)/60p, 1125 (1080)/50p, VGA (640 x 480)-WUXGA*4 (1,920 x 1,200),
compatible with non-interlaced signals only, dot clock: 25-162 MHz
RGB R, B: 0.7 Vp-p, G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms HD,
VD/SYNC: TTL, high impedance, positive/negative automatic
YPBPR(YCBCR) Y: 1.0 Vp-p (including sync signal), PBPR (CBCR): 0.7 Vp-p, 75 ohms
S-Video Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
Video Y: 1.0 Vp-p, 75 ohms
  ET-MCYSD200
SDI IN
SDI IN BNC x 2
3G-SDI SMPTE ST 424 compliant
HD-SDI SMPTE ST 292 compliant
SD-SDI SMPTE ST 259 compliant
  ET-MCYSD210
SDI IN
SDI IN BNC x 4
HD-SDI SMPTE ST 292 compliant
SD-SDI SMPTE ST 259 compliant
  ET-MCQDV150
DVI-U OUT
DVI-U OUT DVI-U 29-pin x 2
Digital DVI 1.0 compliant, compatible with HDCP
RGB/YPBPR(YCBCR) DVI 1.0 compliant, compatible with HDCP
  ET-MCQDL350
DIGITAL LINK OUT RJ-45 x 2
LAN RJ-45 x 1 for network connection, 100Base-TX/10Base-T

*1: Average value. May differ depending on models.

*2: At altitudes of 1,400 m (4,593 ft) or more, the operating temperature range is 0°C to 35°C (32°F to 95°F).

*3: Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)

*4: Compatible with VESA CVT-RB (Reduced Blanking) signals only

NOTES ON USE

  1. Do not install the ET-MWP100G in locations that are subject to excessive water, humidity, steam, or oily smoke.
    Doing so may result in fire, malfunction, or electric shock.
  2. Never place objects on top of the ET-MWP100G while it is operation.
  3. There may be a limited number of interface boards for output that can be installed to the ET-MWP100G 
    because of the number of interface boards for input that are installed. 
    For more information, refer to the “Notification Regarding Restrictions.
  4. If you wish to use the DVI-U board ET-MCYDV100 with the ET-MWP100G, the firmware version of the ET-MWP100G must be V1.19500 or later. 
    For more information, refer to the “Notification.
  5. The signal band that the ET-MWP100G can process is restricted.
    And if the Bandwidth total exceeds 7,200 Mbps, this will result in a reduced frame rate for the output video image. 
    Please use the “Bandwidth Calculator for ET-MWP100G” tool to calculate bandwidth totals.

Terminals