Specifications
Optional AccessoriesMulti Window Processor
ET-MWP100G
ET-MWP100G |
|
---|---|
Power supply | 100–240 V AC, 50/60 Hz |
Power consumption | 160 W max. (180 W with the ET-RPS100G) |
Board mounting slots | 16 slots (including two dedicated input slots and two dedicated output slots) |
Scanning frequency with the ET-MCYSD200 |
|
SDI |
|
Scanning frequency with the ET-MCYSD200/ MCYSD210 |
|
SDI |
|
|
|
Scanning frequency with the ET-MCYDV100 |
|
DVI-U (digital) | fH: 15.6–82.2 kHz, fV: 24.0–85.1 Hz, dot clock: 25.2–162 MHz |
RGB | fH: 15.6–82.2 kHz, fV: 24.0–85.1 Hz, dot clock: 162 MHz or lower |
YPBPR(YCBCR) |
|
Video/S-Video | fH: 15.75 kHz, fV: 60 Hz [NTSC], fH: 15.63 kHz, fV: 50 Hz [PAL] |
Terminals | |
SERIAL IN | D-sub 9-pin (female) x 1 for external control (RS-232C compliant) |
LAN | RJ-45 x 1 for external control, 100Base-TX/10Base-T |
USB | Type A x 1 (front), Type B x 1 (rear), for service |
Dimensions (W x H x D) | 482 x 177 x 313 mm (18-31/32˝ x 6-31/32˝ x 12-5/16˝) |
Weight*1 | Approximately 9.6 kg (21.16 lbs) (when optional devices are mounted) |
Operating environment | Operating temperature: 0–40 °C (32-104 °F)*2, operating humidity: 10–85 % (no condensation) |
Supplied accessories | Power cord (x 3), software CD-ROM (Control Software for Multi Window Processor) |
Optional Interface Boards
ET-MCYDV100 |
|
---|---|
DVI-U IN | |
DVI-U IN | DVI-U 29-pin x 2 |
Digital | DVI 1.0 compliant, compatible with HDCP, for single link only 525i (480i),*3 625i (576i),*3 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/25p, 1125 (1080)/24p, 1125 (1080)/30p, 1125 (1080)/60p, 1125 (1080)/50p, VGA (640 x 480)–WUXGA*4 (1920 x 1200), compatible with non-interlaced signals only, dot clock: 25–162 MHz |
RGB | R, B: 0.7 Vp-p, G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms HD, VD/SYNC: TTL, high impedance, positive/negative automatic |
YPBPR (YCBCR) | Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms |
S-Video | Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms |
Video | Y: 1.0 Vp-p, 75 ohms |
ET-MCYSD200 |
|
---|---|
SDI IN | |
SDI IN | BNC x 2 |
3G-SDI | SMPTE ST 424 compliant |
HD-SDI | SMPTE ST 292 compliant |
SD-SDI | SMPTE ST 259 compliant |
ET-MCYSD210 |
|
---|---|
SDI IN | |
SDI IN | BNC x 4 |
HD-SDI | SMPTE ST 292 compliant |
SD-SDI | SMPTE ST 259 compliant |
ET-MCQDV150 |
|
---|---|
DVI-U OUT | |
DVI-U OUT | DVI-U 29-pin x 2 |
Digital | DVI 1.0 compliant, compatible with HDCP |
RGB/YPBPR (YCBCR) | DVI 1.0 compliant, compatible with HDCP |
ET-MCQDL350 |
|
---|---|
DIGITAL LINK OUT | RJ-45 x 2 |
LAN | RJ-45 x 1 for network connection, 100Base-TX/10Base-T |
*1 Average value. May differ depending on models.
*2 At altitudes of 1,400 m (4,593 ft) or more, the operating temperature range is 0°C to 35°C (32°F to 95°F).
*3 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)
*4 Compatible with VESA CVT-RB (Reduced Blanking) signals only
NOTES ON USE
1. Do not install the ET-MWP100G in locations that are subject to excessive water, humidity, steam, or oily smoke.
Doing so may result in fire, malfunction, or electric shock.
2. Never place objects on top of the ET-MWP100G while it is operating.
3. There may be a limited number of interface boards for output that can be installed to the ET-MWP100G because of the number of interface boards for input that are installed. For more information, refer to the “Notification Regarding Restrictions.”
4. If you wish to use the DVI-U board ET-MCYDV100 with the ET-MWP100G, the firmware version of the ET-MWP100G must be V1.19500 or later. For more information, refer to the “Notification.”
5. The signal band that the ET-MWP100G can process is restricted. And if the Bandwidth total exceeds 7,200 Mbps, this will result in a reduced frame rate for the output video image. Please use the “Bandwidth Calculator for ET-MWP100G” tool to calculate bandwidth totals.
Dimensions
unit: mm (inch)
Terminals
Optional accessories
Interface Board
-
DVI-U Board (2 inputs for DVI-U)
ET-MCYDV100
-
3G-SDI Board (2 inputs for 3G/HD/SD-SDI)
ET-MCYSD200
-
HD-SDI Board (4 inputs for HD/SD-SDI)
ET-MCYSD210
-
DVI-U Board (2 outputs for DVI-U)
ET-MCQDV150
-
DIGITAL LINK Board (2 outputs for DIGITAL LINK,
a LAN connector jack for serial
control and network connection)ET-MCQDL350
Power Supply Unit
-
Power Supply Unit (Additional unit for backup)
ET-RPS100G
- Product Lineup
- Features
- Specifications
- Catalog