PT-TW343R Series

Short Throw LCD Projectors PT-TW343R PT-TW342 PT-TX402 PT-TX312

Specifications

PT-TW343R / PT-TW342

Model PT-TW343R PT-TW342
Power supply AC 100-240 V, 50/60 Hz
Power consumption 300 W
(6 W when STANDBY MODE set to Normal, 0.5 W when STANDBY MODE set to ECO*1)
LCD panel Display method Transparent LCD panel (x 3, R/G/B)
Drive method Active matrix method
Panel size 15.0 mm (0.59 in) diagonal (16:10 aspect ratio)
Pixels 1,024,000 (1,280 x 800) x 3, total of 3,072,000 pixels
Lens Fixed zoom, Manual focus lens, F = 1.8, f = 6.08 mm, Throw Ratio: 0.46:1
Lamp 230 W x 1,
lamp replacement cycle*2 (lamp control: Normal/Eco1/Eco2):
5,000 hours/6,000 hours/10,000 hours
Screen size (diagonal) 1.27-2.54 m (50-100 in) diagonally, 16:10 aspect ratio
Brightness*3
(Lamp control: Normal)
3,300 lm
Center-to-corner uniformity*3 80 %
Contrast*3 12,000:1 (all white/all black, Iris: On)
(Image mode: Dynamic, Lamp control: Normal)
Resolution 1,280 x 800 pixels*4
Scanning
frequency
HDMI IN 525i (480i)*5, 625i (576i)*5, 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p,
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/60p, 1125 (1080)/50p, 1125 (1080)/24p,
1125 (1080)/25p, 1125 (1080)/24sF, 1125 (1080)/30p,
VGA (640 x 480)-WUXGA (1,920 x 1,200),*6 dot clock: 25 MHz-162 MHz
RGB (analog) fH: 15-91 kHz, fV: 24-85 Hz, dot clock: 162 MHz or lower
YPBPR (YCBCR)
fH: 15.73 kHz, fV: 59.94 Hz [480i (525i)],
fH: 31.47 kHz, fV: 59.94 Hz [480p (525p)],
fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p],
fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i],
fH: 28.13 kHz, fV: 25 Hz [1080 (1125)/25p],
fH: 27.00 kHz, fV: 48 Hz [1080 (1125)/24sF],
fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p],
fH: 15.63 kHz, fV: 50 Hz [576i (625i)],
fH: 31.25 kHz, fV: 50 Hz [576p (625p)],
fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p],
fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i],
fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p],
fH: 33.75 kHz, fV: 30 Hz [1080 (1125)/30p],
fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p]
Video/S-Video fH: 15.73 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PAL-M/PAL60],
fH: 15.63 kHz, fV: 50 Hz [PAL/SECAM/PAL-N]
Optical axis shift 7.25:-1 (fixed)
Keystone correction range Vertical: ±15° (Auto, Manual), horizontal: ±15° (Manual)
Installation Ceiling/floor, front/rear
Terminals HDMI IN HDMI 19-pin x 1 (HDCP compatible, Deep Color compatible),
Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
COMPUTER 1 IN D-sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR/S-VIDEO)
(The D-Sub/S-VIDEO conversion cable ET-ADSV is required for inputting S-VIDEO signals.)
COMPUTER 2 IN D-sub HD 15-pin (female) x 1 (RGB)
MONITOR OUT D-sub HD 15-pin (female) x 1 (RGB, Monitor output)
VIDEO IN Pin jack x 1
AUDIO 1 IN M3 x 1 (L-R x 1)
AUDIO 2 IN Pin jack x 2 (L, R x 1)
AUDIO OUT M3 x 1 (L-R x 1) for output (variable)
SERIAL IN D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
LAN RJ-45 x 1
(for network connection, 10BASE-T/100BASE-TX, compliant with PJLink™(class 1))
USB A USB type-A (for the Memory Viewer/Wireless Module,*7 DC 5V max. 500 mA) x 1
USB B USB type-B (for the USB Display) x 1
Mini USB 1 (for interactive function) -
Built-in speaker 10 W (monaural)
Noise level*3 37 dB (lamp control: Normal), 33 dB (lamp control: Eco1), 28 dB (lamp control: Eco2)
Cabinet materials Molded plastic (PC)
Dimensions (W x H x D) 335 x 134.1*8 x 329 mm (13-3/16 x 5-9/32*8 x 12-15/16 in)
Weight*9 Approximately 3.9 kg (8.6 lbs)
Operating temperature 5 °C-40 °C (41 °F-104 °F)
(less than 1,400 m [4,593 ft] above sea level, High land: Off),
5 °C-35 °C (41 °F-95 °F)
(between 1,400 m and 2,700 m [4,593 ft and 8,858 ft] above sea level, High land: On1),
5 °C-30 °C (41 °F-86 °F)
(between 2,700 m and 3,000 m [8,858 ft and 9,843 ft] above sea level, High land: On2)
Operating humidity 20-80 % (no condensation)
Supplied accessories Power cord x 1*10, wireless remote control unit x 1,
batteries (AAA/R03/LR03 type x 2), computer cable x 1,
Interactive Light pen (× 2), Batteries for pen
(R03/LR03/AAA type (× 4)),
USB cable (4.5 m),
Software CD-ROM
(Multi Projector Monitoring &
Control Software*11, LightPen3)
Software CD-ROM
(Multi Projector Monitoring &
Control Software*11)
  • * Product numbers vary depending on the market. The general guideline is as follows:
    The product number in the Americas and Taiwan is PT-TW343RU and PT-TW342U.
    The product number in Europe (except the UK) and CIS is PT-TW343RE and PT-TW342E.
    The product number in the UK, Asia (except Taiwan), Oceania, Middle East, and Africa is PT-TW343RA and PT-TW342A.
*1
When the Standby mode is set to Eco, network functions such as power on over the LAN network will not operate.
Also, only certain commands can be received for external control using the serial terminal.
*2
The value for the recommended lamp replacement cycle is the maximum value, at which luminance will become 50 %.
The usage environment affects the lamp replacement cycle.
*3
Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4
Input signals that exceed this resolution will be converted to 1,280 x 800pixels.
*5
Only compatible with dot clock frequency of 27 MHz (pixel repetition signal).
*6
Compliant with VESA CVT-RB.
*7
To operate wireless projection, the optional ET-WML100 Wireless Module is required.
*8
With legs at shortest position.
*9
The above values are averages. Actual values may be different according to the product.
*10
Power cords available (x 2) for the PT-TW343RA and PT-TW342A.
*11
Compatible with the Multi Monitoring & Control Software.

PT-TX402 / PT-TX312

Model PT-TX402 PT-TX312
Power supply AC 100-240 V, 50/60 Hz
Power consumption 300 W
(6 W when STANDBY MODE set to Normal, 0.5 W when STANDBY MODE set to ECO*1)
LCD panel Display method Transparent LCD panel (x 3, R/G/B)
Drive method Active matrix method
Panel size 16 mm (0.63 in) diagonal (4:3 aspect ratio)
Pixels 786,432 (1,024 x 768) x 3, total of 2,359,296 pixels
Lens Fixed zoom, Manual focus lens, F = 1.8, f = 6.08 mm, Throw Ratio: 0.46:1
Lamp 230 W x 1,
lamp replacement cycle*2 (lamp control: Normal/Eco1/Eco2):
5,000 hours/6,000 hours/10,000 hours
Screen size (diagonal) 1.27-2.54 m (50-100 in) diagonally, 4:3 aspect ratio
Brightness*3
(Lamp control: Normal)
3,800 lm 3,200 lm
Center-to-corner uniformity*3 80 %
Contrast*3 12,000:1 (all white/all black, Iris: On)
(Image mode: Dynamic, Lamp control: Normal)
Resolution 1,024 x 768 pixels*4
Scanning
frequency
HDMI IN 525i (480i)*5, 625i (576i)*5, 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p,
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/60p, 1125 (1080)/50p, 1125 (1080)/24p,
1125 (1080)/25p, 1125 (1080)/24sF, 1125 (1080)/30p,
VGA (640 x 480)-WUXGA (1,920 x 1,200),*6 dot clock: 25 MHz-162 MHz
RGB (analog) fH: 15-91 kHz, fV: 24-85 Hz, dot clock: 162 MHz or lower
YPBPR (YCBCR)
fH: 15.73 kHz, fV: 59.94 Hz [480i (525i)],
fH: 31.47 kHz, fV: 59.94 Hz [480p (525p)],
fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p],
fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i],
fH: 28.13 kHz, fV: 25 Hz [1080 (1125)/25p],
fH: 27.00 kHz, fV: 48 Hz [1080 (1125)/24sF],
fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p],
fH: 15.63 kHz, fV: 50 Hz [576i (625i)],
fH: 31.25 kHz, fV: 50 Hz [576p (625p)],
fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p],
fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i],
fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p],
fH: 33.75 kHz, fV: 30 Hz [1080 (1125)/30p],
fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p]
Video/S-Video fH: 15.73 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PAL-M/PAL60],
fH: 15.63 kHz, fV: 50 Hz [PAL/SECAM/PAL-N]
Optical axis shift 21:-1 (fixed)
Keystone correction range Vertical: ±15° (Auto, Manual), horizontal: ±15° (Manual)
Installation Ceiling/floor, front/rear
Terminals HDMI IN HDMI 19-pin x 1 (HDCP compatible, Deep Color compatible),
Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
COMPUTER 1 IN D-sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR/S-VIDEO)
(The D-Sub/S-VIDEO conversion cable ET-ADSV is required for inputting S-VIDEO signals.)
COMPUTER 2 IN D-sub HD 15-pin (female) x 1 (RGB)
MONITOR OUT D-sub HD 15-pin (female) x 1 (RGB, Monitor output)
VIDEO IN Pin jack x 1
AUDIO 1 IN M3 x 1 (L-R x 1)
AUDIO 2 IN Pin jack x 2 (L, R x 1)
AUDIO OUT M3 x 1 (L-R x 1) for output (variable)
SERIAL IN D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
LAN RJ-45 x 1
(for network connection, 10BASE-T/100BASE-TX, compliant with PJLink™(class 1))
USB A USB type-A (for the Memory Viewer/Wireless Module,*7 DC 5V max. 500 mA) x 1
USB B USB type-B (for the USB Display) x 1
Built-in speaker 10 W (monaural)
Noise level*3 37 dB (lamp control: Normal), 33 dB (lamp control: Eco1), 28 dB (lamp control: Eco2)
Cabinet materials Molded plastic (PC)
Dimensions (W x H x D) 335 x 134.1*8 x 329 mm (13-3/16 x 5-9/32*8 x 12-15/16 in)
Weight*9 Approximately 3.9 kg (8.6 lbs)
Operating temperature 5 °C-40 °C (41 °F-104 °F)
(less than 1,400 m [4,593 ft] above sea level, High land: Off),
5 °C-35 °C (41 °F-95 °F)
(between 1,400 m and 2,700 m [4,593 ft and 8,858 ft] above sea level, High land: On1),
5 °C-30 °C (41 °F-86 °F)
(between 2,700 m and 3,000 m [8,858 ft and 9,843 ft] above sea level, High land: On2)
Operating humidity 20-80 % (no condensation)
Supplied accessories Power cord x 1*10, wireless remote control unit x 1,
batteries (AAA/R03/LR03 type x 2), computer cable x 1,
Software CD-ROM (Multi Projector Monitoring & Control Software*11)
  • * Product numbers vary depending on the market. The general guideline is as follows:
    The product number in Europe (except the UK) and CIS is PT-TX402E and PT-TX312E.
    The product number in the UK, Asia (except Taiwan), Oceania, Middle East, and Africa is PT-TX402A and PT-TX312A.
*1
When the Standby mode is set to Eco, network functions such as power on over the LAN network will not operate.
Also, only certain commands can be received for external control using the serial terminal.
*2
The value for the recommended lamp replacement cycle is the maximum value, at which luminance will become 50 %.
The usage environment affects the lamp replacement cycle.
*3
Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4
Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.
*5
Only compatible with dot clock frequency of 27 MHz (pixel repetition signal).
*6
Compliant with VESA CVT-RB.
*7
To operate wireless projection, the optional ET-WML100 Wireless Module is required.
*8
With legs at shortest position.
*9
The above values are averages. Actual values may be different according to the product.
*10
Power cords available (x 2) for the PT-TX402A and PT-TX312A.
*11
Compatible with the Multi Monitoring & Control Software.
Caution

Do not install the projector in locations that are subject to excessive water, humidity, steam or oily smoke. Doing so may result in fire, malfunction or electric shock.

NOTES ON USE
1 The projector uses a high-voltage mercury lamp under high internal pressure.
This lamp may break, emitting a popping sound, or fail to illuminate, due to impact or extended use.
2 The high-wattage lamp becomes very hot during operation. Please observe the following precautions:
• Never place objects on top of the projector while it is in operation.
• Make sure there is an unobstructed space of 1,000 mm (39-3/8 in) or more around the projector’s exhaust openings.
• If stacking projector units, care must be taken to provide the recommended space between units. These space requirements also apply to installation
  where only one projector unit is operating at one time and the other unit is used as a backup.
• If the projector is placed in a box or enclosure, the temperature of the air surrounding the projector must match the operating temperature listed in the 
  specifications table during use. Also, make sure the projector’s intake and exhaust openings are not blocked. Ensure there is sufficient ventilation to 
  prevent hot air from the exhaust openings being recirculated into the intake opening.
3 The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The lamp replacement cycle varies greatly depending on individual lamp characteristics and usage conditions.
• The brightness of the lamp will gradually decrease with use.
4 Due to natural characteristics of lamps, screen brightness may fluctuate. This is not an indication of faulty lamp performance.